B367 | Insulated Cable Gland For all types of Braid & Tape Armoured Cables

Insulated Industrial Cable Gland

• Metal-to-metal armour clamping
• Permanently crimped, low impedance earth termination
• Secure against self-loosening
• Direct & remote installation
• Enables zoning of earthed neutral systems
• Eliminates circulating currents
• High capacity external earth connection (B367)
• Third party short circuit tested
• Controlled outer ‘load retention’ seal
• Unique OSTG prevents overtightening
• -60°C to +130°C
• EMC tested

† Grooved Cone (X) is predominantly used for Wire Braid (e.g. GSWB, TCWB), Steel Tape Armour (STA, DSTA) and Aluminium Strip Armour (ASA) but is also suitable for Single Wire Armour (SWA), Aluminium Wire Armour (AWA) and Pliable Wire Armour (PWA) if the range is outside that of the Stepped Cone (W).

Note: Grooved Cone (X) dimensions shown in the Cable Gland Selection Table below are for a double wire strand of braid armour cables. Tapes can also be doubled over. For cables that have only a single layer of armour such as SWA the clamping range should be used as shown in the table below.

Note: Earth Tags can only be fitted to the B368 & A368 ZEN Cable Gland types.

The Symmetrical Fault Current (kA) rating for 1 second applicable to the Cast Integral Earth Lug featured in the B367 and A367 products are as follows:
• 26.0 kA for Cable Gland sizes up to 40
• 43.0 kA for Cable Gland sizes 50S and above

Please refer to the CMP CW CIEL product page for dimensional details of the Cast Integral Earth Lug feature included in the B367 and A367 designs.

Aluminium version available for AWA cables. When ordering please substitute letter B in B324 & B348 with letter A.

For under / oversized armour wires click here

Type B367
Design Specification BS 6121:Part 1:1989, IEC 62444, EN 62444, GDCD 190
Mechanical Classifications* Impact = Level 8, Retention = Class D
Enclosure Protection IK10 to IEC 62262 (20 joules) Brass & Stainless Steel only
Electrical Classifications* Category C (B367)
GOST R Certificate POCC.GB.HA46.H00140
Ingress Protection Rating ** IP66
Cable Gland Material Brass, Nickel Plated Brass, Aluminium, Stainless Steel
Seal Material CMP Thermoset Rubber
Cable Type Wire Braid Armour, Pliable Wire Armour (PWA), Steel Tape Armour (STA)
Armour Clamping Three Part Armour Lock With AnyWay Universal Clamping Ring
Sealing Technique Unique CMP ‘LRS’ Outer Seal (Load Retention Seal)
Sealing Area(s) Cable Outer Sheath
Optional Accessories Locknuts, Earth Tags, Serrated Washers, Entry Thread Seals, Shrouds,Ingress Discs
Optional Installation Tools Spanners

Note : * Mechanical & Electrical Classifications applied as per IEC 62444 & EN 62444
** Refer to Maintaining a Seal for further information on Ingress Protection Ratings

Jump to technical illustration   

Certificates

Click here to view Certificates

Product Selection Table

Click here to view how to order

Cable Gland SizeClearance Hole Diameter "C"Cable Bedding Diameter "A"Overall Cable Diameter "B"Armour RangeAcross Flats "D"Across Corners "D"Protrusion Length "F"Ordering Reference (Brass Metric)Cable Gland Weight (Ozs)
MaxMinMaxMinMaxWithout CIEL Lug (B367)
20S0.810.460.370.630.010.040.941.042.3120SB3671RA5.64
200.810.550.490.820.020.041.201.322.3620B3671RA7.76
25S1.010.780.550.870.020.051.481.632.7225SB3671RA11.99
251.010.780.721.030.020.051.481.632.7225B3671RA11.99
321.281.030.931.330.020.051.811.992.6632B3671RA15.52
401.601.261.101.590.020.062.172.382.8840B3671RA25.04
50S2.001.501.391.840.020.062.412.602.8450SB3671RA28.92
502.001.731.592.090.020.062.763.042.9250B3671RA37.39
63S2.511.961.802.340.020.062.953.253.3963SB3671RA53.26
632.512.202.152.590.020.063.153.463.3963B3671RA53.97
75S2.982.442.322.830.020.063.543.903.875SB3671RA74.08
752.982.672.633.090.020.063.944.333.7575B3671RA92.42
903.572.943.003.560.030.064.484.954.2490B3671RA131.92
Dimensions displayed in inches unless otherwise stated
Cable Gland SizeClearance Hole Diameter "C"Cable Bedding Diameter "A"Overall Cable Diameter "B"Armour RangeAcross Flats "D"Across Corners "D"Protrusion Length "F"Ordering Reference (Brass Metric)Cable Gland Weight (Kgs)
MaxMinMaxMinMaxWithout CIEL Lug (B367)
20S20.611.69.515.90.31.024.026.458.620SB3671RA0.16
2020.613.912.520.90.41.030.533.659.920B3671RA0.22
25S25.619.914.022.00.41.237.541.369.125SB3671RA0.34
2525.619.918.226.20.41.237.541.369.125B3671RA0.34
3232.626.223.733.90.41.246.050.667.632B3671RA0.44
4040.632.127.940.40.41.655.060.573.140B3671RA0.71
50S50.738.135.246.70.41.661.266.072.150SB3671RA0.82
5050.744.040.453.00.61.670.177.174.250B3671RA1.06
63S63.749.945.659.40.61.675.082.586.263SB3671RA1.51
6363.755.954.665.80.61.680.088.086.163B3671RA1.53
75S75.761.959.072.00.61.690.099.096.575SB3671RA2.10
7575.767.966.778.40.61.6100.0110.095.375B3671RA2.62
9090.874.976.290.30.81.6114.0125.7107.690B3671RA3.74
Dimensions displayed in millimeters unless otherwise stated

Technical Illustration

Additional Information

Specifying the Correct Alloy Grade

The importance of specifying the correct alloy grade is key when it comes to corrosion prevention, especially if the alloy is to be closely coupled with another metal, otherwise loss of performance may occur through reduced integrity of materials.

Read more

ZEN Insulated Cable Glands

ZEN is available with an insulating arrangement to ensure that no contact is made between the earth circuit carried through the cable armour and the electrical enclosure which the cable enters. This isolation of the cable armour at one end of the cable is sometimes referred to as single point earthing. The ZEN range from CMP however allows more than a single point of earthing and delivering optimum safety.

Read more

Cable Construction

One of the common assumptions when evaluating cables is that the cable will meet the defined IEC 60079-14 requirements and also be compact and circular. At the same time, the surface of the cable bedding may be assumed to be relatively smooth and consistent with the cable outer sheath. In fact this may be the case with some cables, but cables that are manufactured using particularly soft bedding materials, having a low tensile strength, offer a completely different surface finish. This is due to the fact that when cables are produced in high volume facilities, speed is of the essence in order to keep the unit costs down.

Read more

Visit our Knowledge Base for technical expertise and advice, gathered over CMP's 60+ years' experience in the art of terminating cable glands.

Sign up now